Eleanor Norton Audi, 2017-10-13 02:38:01. In the induction tract, the intake valves close well before the piston reaches bottom dead center. This very short opening time keeps the fresh gas flow comparatively small. When the piston moves back up again after reaching bottom dead center, the compression phase starts later than usual. This allows a high geometric compression ratio of 10.0:1 - the combustion then takes place in a relatively small volume. In comparison to the short compression phase, the expansion phase is extended, which results in a high level of efficiency.
Niamh Hart Honda, 2017-10-19 15:02:28. Located behind the instrument panel, the Honda Odyssey cast magnesium steering hanger beam replaces the multi-part steel unit in the previous Odyssey. Its purpose is as a structural attachment point for the steering column and instrument panel, as well as a structural element that helps the passenger cabin retain its shape in certain collisions. For the first time, the Odyssey body structure also utilizes composite materials to further reduce weight while enhancing rigidity and noise dampening. One example is inside the C-pillars, where composite stiffeners, together with the structural foam mentioned above help improve body rigidity. Another example is the base that supports the Odyssey battery. Created from a single composite casting, it holds the battery securely while adding minimal weight to the overall body structure, saving 2.9 lbs. over the previous Odyssey.
Caitlin Duncan Honda, 2017-10-19 15:02:28. Acoustic laminated windshield glass helps reduce noise entering the cabin on EX-L and above trims. Tuned specifically to attenuate wind-, urban- and traffic-noise frequencies, the acoustic windshield uses an outer layer of 2.0 mm safety glass, a 0.7 mm thick middle layer of acoustic polyvinyl butyral (PVB) and a 2.0 mm inner layer for a total thickness of 4.7 mm - an increase over the 4.5mm thickness of the previous-generation Honda Odyssey windshield. This helps the Odyssey place at the top of its class in wind-noise performance.
Niamh Hart Honda, 2017-10-19 15:02:29. Exclusive to the Odyssey Touring and Elite trims, LED low- and high-beam headlights provide improved nighttime illumination and visibility compared to contemporary high-intensity discharge (HID) headlights. Six LEDs serve as low beams and three LEDs serve as high beams on each side. Besides improving driver confidence and passive safety, the LED headlights use less energy, helping to enhance fuel efficiency by reducing engine loads. In addition, the LED headlights last up to five times longer than HID headlights and up to 10 times longer than halogen headlights - contributing to less frequent replacement and the associated cost savings. An auto on/off function is also included.
Millie Lowe Honda, 2017-10-19 15:02:30. Along with acoustic spray foam applied in 14 critical locations, all Odyssey trims feature triple door seals and Active Noise Control technology to help prevent unwanted noise from reaching the passengers. While all trims benefit from thicker front and rear door glass, Elite receives acoustic front/rear door glass and adds an additional carpet barrier layer, acoustic fabric fender liners, additional slide door insulation, and rear wheelhouse insulators.
Mollie Slater Honda, 2017-10-19 15:02:29. The 2018 Honda Odyssey incorporates a wide range of halogen and light-emitting diode (LED) exterior lighting features. LED headlights are available for the first time, joining available LED Daytime Running Lights (DRL), available LED side mirror turn signals and LED taillights to provide the brightest and most visually distinctive array of Odyssey exterior lighting yet.
Mollie Slater Honda, 2017-10-19 15:02:29. The Odyssey V6 engine combines Variable Cylinder Management (VCM) with Variable Valve Timing and Lift Electronic Control (i-VTEC), which changes the lift profile, timing and lift duration of the intake valves. A switching mechanism allows each cylinder to operate with low-rpm valve lift and duration or high-rpm lift and duration. While operating in 3-cylinder mode, the rear cylinder bank rocker arms deactivate, closing all intake and exhaust valves to minimize pumping losses. The "intelligent" portion of the system is its ability to vary valve operation based on the driving situation and engine rpm. At low rpm, the i-VTEC intake valve timing and lift are optimized (low lift, short duration) for increased torque, which allows a wide range of 3-cylinder operation. As engine rpm builds past 5,350 rpm, the i-VTEC system transitions to a high-lift, long-duration intake cam profile for superior high-rpm engine power.
Shannon Griffin Honda, 2017-10-19 15:02:28. Multiple grades of high-strength steel are used in the Odyssey body construction to help achieve excellent overall vehicle dynamics, optimize safety performance, reduce weight, and lower noise, vibration and harshness (NVH). The combination of advanced materials and evolved engineering processes save 75 lbs. in unit-body weight compared to the previous-generation Odyssey. The 2018 Honda Odyssey features several unique advancements in body design and materials that significantly improve overall rigidity, while reducing weight. This directly helps improve overall vehicle dynamics, crash safety performance, interior quietness, and long-term durability.
Any content, trademark/s, or other material that might be found on this site that is not this site property remains the copyright of its respective owner/s. In no way does tnahid claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.