Mollie Slater Ford Fiesta, 2017-11-04 19:54:16. Additional testing during and after production further enhances quality. A new manufacturing technology analyses the noise frequencies produced during the stamping process, and can identify a component that does not meet quality standards before it leaves the press. "We’ve paid a lot of attention to elements and features that customers notice without realising it, from panel gaps to pedal feel," Palmer said. "Fiesta is one of the most universal sights on the road, and our goal was to deliver a car that would inspire an admiring glance every time."
Caitlin Duncan Audi, 2017-10-13 03:01:57. As an alternative to the further-developed electromechanical power steering, Audi also offers dynamic steering with RS-specific tuning. This uses a superposition gear to vary its ratio by up to 100 percent, depending on the car‘s speed and the mode selected in the Audi drive select dynamic handling system. At the cornering limits, the system countersteers with tiny impulses, thus further boosting the dynamism and driving safety. In the dynamic setting within Audi drive select, the superposition of the dynamic steering is stiff in order to support a more sporty driving style.
Caitlin Duncan Audi, 2017-10-13 15:16:50. Both turbochargers of the 2.9 TFSI unit are centrally positioned inside the V of the engine and each of them supplies a single cylinder bank. The B-cycle combustion process with central direct injection represents a new level of efficiency within the RS family. In the NEDC, the V6 bi-turbo consumes just 8.7 liters of fuel per 100 kilometers (27.0 US mpg), which corresponds to 197 grams of CO2 per kilometer (317.0 g/mi). This is an efficiency gain of 17 percent over the previous model. Also beneficial for the new Audi RS5 Coupe is a drastic reduction in weight. The vehicle weighs in at 1,655 kilograms (3,648.7 lb) - 60 kilograms (132.3 lb) less than previously. A carbon roof with visible fiber structure is also available as an option.
Eleanor Norton Audi, 2017-10-13 15:52:01. The fast, spontaneously and sportily shifting eight-speed tiptronic with optimized shift times is standard on the new Audi RS5 Coupe. The layout of its gear sets and shifting elements results in low drag torques and thereby to a high efficiency level. Its large number of gears very frequently makes it possible to operate the engine close to its ideal load point. The lower gears have short, sporty ratios, while the upper gears are long in order to reduce revs and fuel consumption.
Shannon Griffin Ford Fiesta, 2017-10-13 02:45:51. The agile and responsive Ford Performance-tuned chassis will be supported by enhanced Torque Vectoring Control technology that improves road holding and reduces understeer by applying brake force to the inside front wheel when cornering. Three-mode ESC will enable drivers to choose between full system intervention; wide-slip mode with limited intervention; and full system de-activation. Greater personalisation.
Mollie Slater Audi, 2017-10-13 02:58:07. In the induction tract, the intake valves close well before the piston reaches bottom dead center. This very short opening time keeps the fresh gas flow comparatively small. When the piston moves back up again after reaching bottom dead center, the compression phase starts later than usual. This allows a high geometric compression ratio of 10.0:1 - the combustion then takes place in a relatively small volume. In comparison to the short compression phase, the expansion phase is extended, which results in a high level of efficiency.
Libby Wade Audi, 2017-10-13 02:52:55. The chain drive uses a new concept to reduce the drive power required: the crankshaft drives the balancer shaft via gears, with the shaft lying far down in the V of the cylinder banks. From here chains run to the four camshaft sprockets. These are trioval in shape, i.e. they have a slightly triangular shape, in order to compensate for peak forces. The balancer shaft rotates on roller bearings with particularly low levels of friction.
Millie Lowe Ford Fiesta, 2017-10-13 03:03:44. Additional testing during and after production further enhances quality. A new manufacturing technology analyses the noise frequencies produced during the stamping process, and can identify a component that does not meet quality standards before it leaves the press. "We’ve paid a lot of attention to elements and features that customers notice without realising it, from panel gaps to pedal feel," Palmer said. "Fiesta is one of the most universal sights on the road, and our goal was to deliver a car that would inspire an admiring glance every time."
Any content, trademark/s, or other material that might be found on this site that is not this site property remains the copyright of its respective owner/s. In no way does tnahid claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.