Kiera Shaw BMW, 2017-11-04 19:54:23. The BMW i8 Protonic Frozen Yellow Edition - which will be produced in a limited run and go on sale in September 2017 - owes its striking appearance to a model-specific paint finish. The exclusive exterior shade Protonic Frozen Yellow shares its canvas with accents in Frozen Grey metallic. A sophisticated application process is employed to transfer the paint to the BMW i8‘s carbon fibre-reinforced plastic (CFRP) bodywork. The silky-matt shimmer of the finish shines a particularly vivid spotlight on the plug-in-hybrid sports car‘s dynamic lines and flowing surface design. The special-edition model will sport newly designed 20-inch BMW i light-alloy wheels in W-Spoke design with mattpainted surfaces and mixed-size tyres.
Paige Dodd Honda, 2017-10-19 15:02:27. Located under the front floor of the new Honda Odyssey is a variation of the "3-Bone" structure used in the Pilot that improves impact load management, directing energy around the passenger cabin in the event of a frontal collision. The structure creates three different load pathways, or "backbones," that channel collision energy. One channels collision forces from the front of the vehicle directly underneath the passenger cabin; the other two channel collision forces under the vehicle left and right side frames. The result is an improved capability to safely channel energy during a frontal crash.
Niamh Hart Honda, 2017-10-18 23:58:59. Compared to conventional halogen headlights, the Odyssey available LED headlights offer some 32.8 feet (10 meters) wider illuminated area on each side - as well as a 26.2 foot (8 meter) longer reach line - when low beams are in use. The width and reach advantages aid drivers in more safely and confidently navigate both straight and winding roads. Odyssey auto-high beam feature further improves safety. All 2018 Odyssey trims feature LED taillights, whose C-shaped design complements the wing-shaped design of the available front LED DRLs and providing a distinctive Odyssey appearance that is easy to spot on the road. The Odyssey EX-L, Touring and Elite trims feature a power tilting and sliding front moonroof with a manual sunshade. To tilt or slide the moonroof, the driver or front passenger needs only to fully press the ceiling-mounted switch once (instead of pressing and holding it for several seconds). The moonroof fully opens or closes automatically. However, if the operator wishes to only partially open or close the moonroof (such as to achieve partial ventilation), a lighter touch yields fully manual control. The moonroof can also tilt to provide ventilation. An auto-reverse feature is built in, helping to mitigate the possibility of a pinched finger or limb. If the moonroof motor ECU detects a threshold level of mechanical resistance, indicating a possible obstruction, the motor will automatically reverse and reopen the moonroof.
Paige Dodd Honda, 2017-10-18 23:59:20. The new fifth-generation Odyssey is a progressive and sporty evolution of the Odyssey well-known exterior form. In front, the 2018 model includes the latest version of Honda trapezoid grille, with boldly restyled chrome bars, stylized headlights, and new wing-shaped LED daytime running lights (DRL) lending a premium appearance on EX and above models. Bright LED headlights and fog lights complete the Touring and Elite trims. The hood gains new character lines that add a more visually enticing and sophisticated look, while the front fascia invokes a sports sedan, with a large lower air inlet.
Eleanor Norton Honda, 2017-10-19 00:00:12. Exclusive to the Odyssey Touring and Elite trims, LED low- and high-beam headlights provide improved nighttime illumination and visibility compared to contemporary high-intensity discharge (HID) headlights. Six LEDs serve as low beams and three LEDs serve as high beams on each side. Besides improving driver confidence and passive safety, the LED headlights use less energy, helping to enhance fuel efficiency by reducing engine loads. In addition, the LED headlights last up to five times longer than HID headlights and up to 10 times longer than halogen headlights - contributing to less frequent replacement and the associated cost savings. An auto on/off function is also included.
Shannon Griffin Honda, 2017-10-18 23:59:37. Along with acoustic spray foam applied in 14 critical locations, all Odyssey trims feature triple door seals and Active Noise Control technology to help prevent unwanted noise from reaching the passengers. While all trims benefit from thicker front and rear door glass, Elite receives acoustic front/rear door glass and adds an additional carpet barrier layer, acoustic fabric fender liners, additional slide door insulation, and rear wheelhouse insulators.
Caitlin Duncan Honda, 2017-10-18 23:59:56. The 2018 Odyssey receives the most thorough and intensive array of aerodynamic refinements of any Odyssey generation to date. This comprehensive approach boosts aerodynamic efficiency and reduces wind noise. Examples of the aero efforts found on the 2018 Odyssey include extensive under covers, the Active Shutter Grille system, hidden windshield wipers, wind-sculptured side mirrors (power folding on Elite), and many small but pertinent details such as under-body strakes, shark fin-type antenna, and a rear spoiler (black on LX, EX, EX-L and Touring trims, body-color on Elite).
Caitlin Duncan Honda, 2017-10-19 15:02:27. The Odyssey new engine - from the Honda EarthDreams® Technology powertrain series - is rated at 280 peak horsepower and 262 lb.-ft. peak torque. Peak engine output is up 32 horsepower and 12 pound-feet of torque from the previous model, with increased torque over the engine entire operating (rpm) range. The new, more efficient engine and transmissions, along with as much as a 75-pound reduction in vehicle weight (EX-L trim) and improved aerodynamics, among other reductions to running resistance, result in enhanced performance and fuel efficiency. With its 60-degree V-angle, the Odyssey V6 engine is inherently smooth and has compact overall dimensions that allow efficient packaging within the vehicle. The engine has a high-pressure die-cast lightweight aluminum alloy block with cast-in-place iron cylinder liners. Made with a centrifugal spin-casting process, the thin-wall liners are high in strength and low in porosity. The block incorporates a deep-skirt design with four bolts per bearing cap for rigid crankshaft support and minimized noise and vibration. The engine also uses a high-tensile strength steel crankshaft is for minimum weight.
Any content, trademark/s, or other material that might be found on this site that is not this site property remains the copyright of its respective owner/s. In no way does tnahid claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.